1006 EX EXTERNAL IGNITION - 1006-EX

$0.00
(No reviews yet) Write a Review
SKU:
1006-EX
1990-94 1340 EVOLUTION- BIG-TWIN- AND 1990-93 883 XLH SPORTSTER- WITH 7 PIN CANNON PLUG

EVOLUTION&OGRAVE INTERNAL IGNITION FEATURING STAGE RPM LIMIT

&MIDDOT WIDE TIMING ADVANCE ADJUSTMENT RANGE ACCOMMODATES STOCK TO HIGHLY MODIFIED ENGINES

&MIDDOT DIGITALLY SET RPM LIMIT (100 RPM STEPS)

&MIDDOT SELECTABLE SINGLE OR DUAL FIRE MODE

&MIDDOT SELECTABLE MULTI-SPARK MODE FOR QUICK STARTING AND SMOOTH CRUISE

&MIDDOT COIL OUTPUTS PROTECTED AGAINST SHORT CIRCUITS

&MIDDOT OPTIONAL USB INTERFACE AND SOFTWARE FOR PROGRAMMING CUSTOM ADVANCE CURVE

&MIDDOT BILLET ALUMINUM HOUSING WITH BLACK ANODIZED FINISH

&MIDDOT EASY PLUG-IN INSTALLATION
TWO PART NUMBERS ARE AVAILABLE. THE DIFFERENCE IS IN THE MATING CONNECTOR. MODEL 1006 HAS A 7 PIN CONNECTOR AND IS INTENDED FOR 1990-1994 H-D® MOTORCYCLES. MODEL 1007 HAS AN 8 PIN CONNECTOR AND IS INTENDED FOR LATER MODELS. THE EXTERNAL MODULE OFFERS EASY PLUG-IN INSTALLATION AND IS IDEAL AS A DO-IT-YOURSELF ITEM. MODELS 1006 AND 1007 ARE INTENDED FOR ELECTRIC START APPLICATIONS ONLY AND ARE NOT COMPATIBLE WITH KICK START ENGINES.

THE UNIT IS CONSTRUCTED WITH A LOW PROFILE MACHINED BILLET ALUMINUM HOUSINGS. WITH THE EXCEPTION OF EXTERNAL MOUNTING AND PLUG-IN CONNECTION ALL OTHER FEATURES ARE THE SAME AS THE MODEL 1005 INTERNAL IGNITION. FOUR ROTARY SWITCHES ARE USED TO SET THE OPERATING MODES (SUCH AS SINGLE OR DUAL FIRE) ADJUST THE TIMING ADVANCE AND SELECT THE RPM LIMIT. TWO DIAGNOSTIC LEDS INDICATE STATUS AND THE STATE OF THE VACUUM SWITCH (VOES). THE STATUS LED IS ALSO USED FOR STATIC TIMING AS IT WILL FLASH WHEN THE ENGINE REACHES TOP DEAD CENTER (TDC).

YOU CAN ADJUST THE SLOPE OF THE ADVANCE CURVE. THE USER CAN OPTIMIZE THE TIMING ADVANCE FOR A WIDE RANGE OF APPLICATIONS - FROM STOCK TO HIGHLY MODIFIED ENGINES. FOR DETAILS INCLUDING ADVANCE CURVES YOU CAN DOWNLOAD THE INSTALLATION INSTRUCTIONS FROM OUR WEBSITE.

SWITCH SELECTABLE SINGLE OR DUAL FIRE MODE ALLOWS YOU TO INITIALLY INSTALL THE UNIT AND RUN IT IN DUAL FIRE MODE WITH YOUR STOCK COIL. YOU CAN THEN EASILY UPGRADE TO SINGLE FIRE BY ADDING AN APPROPRIATE COIL. IF YOU HAVE A TACH IT WILL CONTINUE TO OPERATE PROPERLY (SOME COMPETITIVE SYSTEMS REQUIRE THAT YOU PURCHASE A TACH ADAPTER).

A SPECIAL FEATURE ALLOWS USE OF THE TACHOMETER WIRE FOR A LINK TO A LAPTOP PC WHEN THE ENGINE IS NOT RUNNING. WHILE THE CUSTOMER DOES NOT REQUIRE THE PC LINK FOR ANY NORMAL SETUP OR OPERATION IT CAN BE USED TO ACCESS ADDITIONAL FEATURES FOR PRECISE DYNO TUNING (SUCH AS PROGRAMMING A CUSTOM ADVANCE CURVE AND SETTING REAR CYLINDER TIMING OFFSET). OUR NEW USB INTERFACE IS USED FOR THIS PURPOSE. THE USB INTERFACE IS SOLD SEPARATELY BUT WINDOWS COMPATIBLE SOFTWARE IS AVAILABLE FOR DOWNLOAD. THE SOFTWARE WILL OPERATE IN DEMO MODE WITHOUT AN IGNITION ATTACHED.

SPORTSTER® 1200S WITH DUAL PLUG HEADS
THE SPORTSTER®1200S MODEL WITH DUAL PLUG HEADS COMES WITH A SPECIAL IGNITION MODULE SIMILAR TO THAT USED ON TWIN-CAM 88® MODELS. IF YOU REQUIRE A PROGRAMMABLE AFTERMARKET IGNITION FOR THE 1200S WE HAVE THE SOLUTION. YOU CAN USE OUR EXTERNAL IGNITION VERSION 1007 (NOT THE 1005S). THE ORIGINAL EQUIPMENT COIL HAS LOW RESISTANCE PRIMARY WINDINGS THAT ARE NOT COMPATIBLE WITH OUR IGNITION. YOU MUST REPLACE THE ORIGINAL EQUIPMENT COIL WITH AN AFTERMARKET FOUR TOWER COIL SUCH AS THE DYNA DC6-4 THAT HAS 3 OHM PRIMARY RESISTANCE. PLEASE REFER TO OUR DUAL SPARK PLUG TECH NOTE FOR MORE DETAILS. YOU WILL HAVE TO REMOVE THE ORIGINAL EQUIPMENT MAP SENSOR. YOU WILL ALSO REQUIRE OUR TIMING ROTOR (P/N 18004) AND VOES SWITCH (P/N 18010).

Instructions: https://www.jmschip.com/content/DTT/INSTRUCTIONS/1006-EX_Instruction.pdf