WIDE TIMING ADVANCE ADJUSTMENT RANGE ACCOMMODATES STOCK TO HIGLY MODIFIED ENGINES.
&MIDDOT DIGITALLY SET RPM LIMIT (100 RPM STEPS)
&MIDDOT SELECTABLE SINGLE OR DUAL FIRE MODE
&MIDDOT SELECTABLE MULTI-SPARK MODE FOR QUICK STARTING AND SMOOTH CRUISE
&MIDDOT COIL OUTPUTS PROTECTED AGAINST SHORT CIRCUITS
&MIDDOT OPTIONAL USB INTERFACE AND SOFTWARE FOR PROGRAMMING A CUSTOM ADVANCE CURVE
&MIDDOT BILLET ALUMINUM HOUSING
THE MODEL 1005 INTERNAL IGNITION UNIT IS TRIGGERED FROM THE STOCK TIMING ROTOR AT THE END OF THE CAMSHAFT AND MOUNTED WITHIN THE NOSE CONE OF THE ENGINE. THIS NOSE CONE IGNITION IS APPLICABLE TO A WIDE RANGE OF H-D® ENGINES. THE MODEL 1005 IGNITION REPLACES ALL THE H-D® OE IGNITION COMPONENTS INCLUDING THE BULKY WIRING HARNESS AND EXTERNAL MODULE. THE RESULTING CLEAN APPEARANCE IS ESPECIALLY DESIRABLE ON CUSTOM MOTORCYCLES. THE 50 STATES STREET LEGAL MODEL 1005 EX VERSION FITS ALL 1970-1984 SHOVELHEAD® BIG-TWIN® ENGINES 1986-93 883 XLH SPORTSTER® ENGINES 1986-87 1100 XLH SPORTSTER® ENGINES AND 1984-1999 1340 EVOLUTION® BIG-TWIN® ENGINES AND FEATURES ADVANCE CURVES SUITABLE FOR ALL STREET APPLICATIONS INCLUDING HIGH COMPRESSION ENGINES. THE MODEL 1005 RACE VERSION FITS ALL 1970-1984 SHOVELHEAD® BIG-TWIN® ENGINES 1971-1997 SPORTSTER® ENGINES AND 1984-1999 EVOLUTION® BIG-TWIN® ENGINES AND INCLUDES RACE ADVANCE CURVES WITH A SLIGHTLY WIDER ADJUSTMENT RANGE. THE 50 STATES STREET LEGAL MODEL 1005S EX FITS 1998-2003 SPORTSTER® ENGINES (EXCEPT DUAL PLUG 1200S) AND DIRECTLY PLUGS INTO THE OE WIRING HARNESS (THESE LATE MODELS CAME WITH AN OE INTERNAL IGNITION). THE MODEL 1005S EX HAS ADVANCE CURVES OPTIMIZED FOR THESE SPORTSTER® APPLICATIONS.
THE MODEL 1005 IS CONSTRUCTED WITH A LOW PROFILE MACHINED BILLET ALUMINUM HOUSING. FOUR ROTARY SWITCHES ARE USED TO SET THE OPERATING MODES (SUCH AS SINGLE OR DUAL FIRE ADVANCE CURVE FAMILY AND MULTI-SPARK) ADJUST THE TIMING ADVANCE AND SELECT THE RPM LIMIT. TWO DIAGNOSTIC LEDS INDICATE STATUS AND THE STATE OF THE VACUUM SWITCH (VOES). THE STATUS LED IS ALSO USED FOR STATIC TIMING AS IT WILL FLASH WHEN THE ENGINE REACHES TOP DEAD CENTER (TDC).
YOU CAN ADJUST THE SLOPE OF THE ADVANCE CURVE. THE USER CAN OPTIMIZE THE TIMING ADVANCE FOR A WIDE RANGE OF APPLICATIONS - FROM STOCK TO HIGHLY MODIFIED ENGINES. FOR DETAILS INCLUDING ADVANCE CURVES YOU CAN DOWNLOAD THE INSTALLATION INSTRUCTIONS FROM OUR WEBSITE.
SWITCH SELECTABLE SINGLE OR DUAL FIRE MODE ALLOWS YOU TO INITIALLY INSTALL THE UNIT AND RUN IT IN DUAL FIRE MODE WITH YOUR STOCK COIL. YOU CAN THEN EASILY UPGRADE TO SINGLE FIRE BY ADDING AN APPROPRIATE COIL. IF YOU HAVE A TACH IT WILL CONTINUE TO OPERATE PROPERLY (SOME COMPETITIVE SYSTEMS REQUIRE THAT YOU PURCHASE A TACH ADAPTER).
A SPECIAL FEATURE ALLOWS USE OF THE TACHOMETER WIRE FOR A LINK TO A LAPTOP PC WHEN THE ENGINE IS NOT RUNNING. WHILE THE CUSTOMER DOES NOT REQUIRE THE PC LINK FOR ANY NORMAL SETUP OR OPERATION IT CAN BE USED TO ACCESS ADDITIONAL FEATURES FOR PRECISE DYNO TUNING (SUCH AS PROGRAMMING A CUSTOM ADVANCE CURVE AND SETTING REAR CYLINDER TIMING OFFSET). OUR NEW USB INTERFACE IS USED FOR THIS PURPOSE. THE USB INTERFACE IS SOLD SEPARATELY BUT WINDOWS COMPATIBLE SOFTWARE IS AVAILABLE FOR DOWNLOAD. THE SOFTWARE WILL OPERATE IN DEMO MODE WITHOUT AN IGNITION ATTACHED.
KICK START CAPABILITY
THE MODEL 1005 IS PRIMARILY INTENDED FOR ELECTRIC START APPLICATIONS. HOWEVER REV 7.0 UNITS (MANUFACTURED AFTER JANUARY 2006) CAN BE PROGRAMMED FOR KICK START MODE BY USING OUR PC LINK EVO SOFTWARE AND OPTIONAL USB INTERFACE. IF YOU ORDER ON-LINE YOU CAN ADD A NOTE STATING THAT YOU REQUIRE KICK START CAPABILITY AND WE WILL PROGRAM THE UNIT FOR YOU AT NO EXTRA COST. WHEN PROGRAMMED FOR KICK START MODE THE UNIT HAS ZERO CRANKING DELAY AND A 30 SECOND TIMEOUT BEFORE COIL CURRENT SHUTOFF.
SPORTSTER® 1200S WITH DUAL PLUG HEADS
THE SPORTSTER®1200S MODEL WITH DUAL PLUG HEADS COMES WITH A SPECIAL IGNITION MODULE SIMILAR TO THAT USED ON TWIN-CAM 88® MODELS. IF YOU REQUIRE A PROGRAMMABLE AFTERMARKET IGNITION FOR THE 1200S WE HAVE THE SOLUTION. YOU CAN USE OUR EXTERNAL IGNITION VERSION (NOT THE 1005S). THE ORIGINAL EQUIPMENT COIL HAS LOW RESISTANCE PRIMARY WINDINGS THAT ARE NOT COMPATIBLE WITH OUR IGNITION. YOU MUST REPLACE THE ORIGINAL EQUIPMENT COIL WITH AN AFTERMARKET FOUR TOWER COIL SUCH AS THE DYNA DC6-4 THAT HAS 3 OHM PRIMARY RESISTANCE. PLEASE REFER TO OUR DUAL SPARK PLUG TECH NOTE FOR MORE DETAILS. YOU WILL HAVE TO REMOVE THE ORIGINAL EQUIPMENT MAP SENSOR. YOU WILL ALSO REQUIRE OUR TIMING ROTOR (P/N 18004) AND VOES SWITCH (P/N 18010).
Instructions: https://www.jmschip.com/content/DTT/INSTRUCTIONS/1005_Instructions.pdf
